Differences

This shows you the differences between two versions of the page.

--- arm:dreamplugbasics [2012/07/23 14:12] – RichardNeese
+++ arm:dreamplugbasics [2019/07/09 19:03] (current) – add EOL announcement from GlobalScale. MarkLinimon
@@ Line 1: / Line 1: @@
+:!: [[https://mailchi.mp/globalscaletechnologies/globalscale-announces-end-of-life-and-last-time-buy-for-sheevaplug-guruplug-and-dreamplug|DreamPlug EOL announcement 20190709]]
 Basic Device Setup at time of shipment
 Single drive boot (internal sd only)
@@ Line 92: / Line 94: @@
 setenv serverip  <server-ip>
 setenv ipaddr    <board-ip-addr>
-saveenv netmask   <netmask>
+setenv netmask   <netmask>
 setenv gatewayip <gateway-ip>
 saveenv
@@ Line 98: / Line 100: @@
 </code>
-U-Boot [[/MultiBoot|MultiBoot]]
+U-Boot %%MultiBoot%%
 <code>
 This setup will allow you to boot off usb/esata/external-sd/internal-sd.
-It will auto test all 3 in order of sdb >> sdb >> sda
+It will auto test all 4 in order of sdd >> sdc >> sdb >> sda
+currently when it hits the go 0x00900000 it will hang.
+This is due to the fact go is a cmd statement telling it to load a specific Memory segment.
+We are working to get ukernels working. so then the multi boot for uboot will work correctly.
 Enter the following lines to enable multiboot:
@@ Line 113: / Line 121: @@
 setenv x_bootcmd_ethernet
-Now Set new values: sda = internal linux sd
+Now Set new values: sda = internal linux sd / da0 = internal Freebsd
-                    db1 = external BSD sd
+                    da1 = external FreeBSD sd
-                    da2 = 1st external usb drive or esata
+                    da2 = 1st external FreeBSD usb drive or esata
-                    da3 = 1st external usb drive or esata if drive da1 is pluggedinto usb
+                    da3 = 1st external Freebsd usb drive or esata if drive da2 is plugged into usb
 setenv bootdelay 3
@@ Line 163: / Line 171: @@
 DEVICE_ARCH="arm"                       # Device Archutecture
 DEVICE_KERNEL="DREAMPLUG"		# ls /usr/src/sys/conf and find your cpu
-drive=da0                               # da0/da1/da2/da3
+export DRIVE=da0                        # da0/da1/da2/da3
 ######### DO NOT EDIT ############### Envirmental settings for build ################
 OBJDIR="/usr/obj/${DEVICE_ARCH}.${DEVICE_ARCH}/usr/"
@@ Line 171: / Line 179: @@
 ####Build SD/HD########
-dd if=/dev/zero of=/dev/${drive} bs=512 count=1
+dd if=/dev/zero of=/dev/'${DRIVE}' bs=512 count=1
-gpart create -s mbr da0
+gpart create -s mbr '${DRIVE}'
-gpart add -s32m -t \!14 ${drive}
+gpart add -s32m -t \!14 '${DRIVE}'
-gpart set -a active -i 1 ${drive}
+gpart set -a active -i 1 '${DRIVE}'
-gpart add -t freebsd ${drive}
+gpart add -t freebsd '${DRIVE}'
-newfs_msdos -F 16 /dev/${drive}s1
+newfs_msdos -F 16 /dev/'${DRIVE}'s1
-newfs /dev/${drive}s2
+newfs /dev/'${DRIVE}'s2
-mount -t msdosfs /dev/${drive}s1 /mnt/1
+mount -t msdosfs /dev/'${DRIVE}'s1 /mnt/1
-mount /dev/${drive}s2 /mnt/2
+mount /dev/'${DRIVE}'s2 /mnt/2
 ######## port checking script ########