A_Brief_Guide_To_Cross_Compiling_FreeBSD [FreeBSD WIKI]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Cross Compiling FreeBSD for Fun and Profit ======

===== Summary =====

  * Introduction
  * Obtaining %%FreeBSD%%
  * Setting up Build Environment
  * Building World
  * What's Next
  * Cheatsheet

===== Introduction =====

==== Notes ====

For the sake of illustration, the document assumes that:

  * All files will be placed under ///home/bob// .
  * The architecture being built will be (big-endian) ARM, aka //armeb//.
  * The installed world will be placed under ///home/bob/my-armeb//.

==== Notation Used ====

  * Any line preceded by a //%// is to be executed in a system shell.
  * The reader can specify make variables in one of three ways:
    * In a custom //make.conf// file and call make with \_\_MAKE_CONF=/full/path/to/make.conf .
    * Set the variables in the environment, e.g. with env, export, or setenv.
    * Explicitly on the command line. **NOTE**: this is how the writeup specifies the values.

===== Obtaining FreeBSD =====

The reader can obtain the sources as noted in the Handbook chapter titled [[http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/mirrors.html|Obtaining FreeBSD]]. The reader should place the sources in ///home/bob/src//.

===== Setting up Build Environment =====

For architectures that are supported by %%FreeBSD%%, cross-building is relatively easy. For architectures that %%FreeBSD%% doesn't support, more work is required.

The %%FreeBSD%% build system uses three environment variables to control which platform to build (TARGET), which target architecture to build (TARGET_ARCH), and where to put the results (MAKEOBJDIRPREFX). By default, %%FreeBSD%% builds the current architecture and places the results in ///usr/obj//, or in this example ///home/bob/obj//.

When cross-compiling however, %%FreeBSD%% places binaries in //$MAKEOBJDIRPREFIX/$TARGET// (for cases where //$TARGET// == //$TARGET_ARCH//, e.g. amd64) or //$MAKEOBJDIRPREFIX/$TARGET.$TARGET_ARCH// (for cases where //$TARGET// != //$TARGET_ARCH//). In this example, the directory used will be ///home/bob/obj/arm.armeb//.

Note that a non-default value of MAKEOBJDIRPREFIX must be passed to make as an environment variable.  It cannot be set as an argument to make directly.

==== make.conf / src.conf ====

A standard make.conf and src.conf file can contain variables or make snippets which tune build behavior. /usr/share/examples/etc/make.conf has more details on some recommended make.conf tunable items, and src.conf(5) lists some of the variables that one could put in src.conf . The following notes some potential pitfalls in using these files for cross-compiling, make universe, make tinderbox, etc:

  * Explicitly setting CPUTYPE. The following incorrect example would explicitly attempt to build binaries optimizing for the core2 Intel architecture:

<code>
CPUTYPE= core2
</code>

The reader should instead set the CPUTYPE as follows:

<code>
CPUTYPE?= core2
</code>

  * Explicitly setting KERNCONF. The following incorrect example would explicitly build the XEN KERNCONF (which only exists for i386 and amd64):

<code>
KERNCONF= XEN
</code>

The reader should instead set KERNCONF as follows:

<code>
KERNCONF?= XEN
</code>

===== Building and Installing World =====

The following subsections show the reader how they could build and install world for the big-endian ARM architecture from scratch.

==== Go to the Source Directory ====

<code>
% cd /home/bob/src
</code>

==== Build World ====

<code>
% env MAKEOBJDIRPREFIX=/home/bob/obj make buildworld TARGET=arm TARGET_ARCH=armeb
</code>

==== Install World ====

  * First and foremost, one must create the install directory:

<code>
% mkdir /home/bob/my-armeb
</code>

  * Then one must run make installworld to install the binaries produced in buildworld:

<code>
% env MAKEOBJDIRPREFIX=/home/bob/obj make installworld DESTDIR=/home/bob/my-armeb TARGET=arm TARGET_ARCH=armeb
</code>

  * And last but not least, one must run make distribution to populate the world with important files from ///etc//:

<code>
% env MAKEOBJDIRPREFIX=/home/bob/obj make distribution DESTDIR=/home/bob/my-armeb TARGET=arm TARGET_ARCH=armeb
</code>

**NOTE**: You could invoke mergemaster instead of running make distribution; mergemaster does a few things that make distribution does not do; see [[http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html|The Canonical Way to Update Your System]] for more details, and please consult mergemaster(8).

===== What's Next =====

The above example demonstrated how one could build world and install world with armeb. This should provide you with the building blocks required to build the %%FreeBSD%% base system for any cross-compilation environment.

===== Cheat sheet =====
http://lists.freebsd.org/pipermail/freebsd-current/2006-July/064384.html

----

{{tag>Stale}}