The original Raspberry Pi launched in early 2012 as an inexpensive ($35) PC based on a Broadcom BCM2835 SoC. It was developed by the UK-based Raspberry Pi foundation as an inexpensive system for educational use. As of April 2013, it had sold over a million units.

There are many versions of the Raspberry Pi. Where links are shown, they lead to information about models currently being sold.

Due to the bewildering number of versions, some earlier versions are not listed here.

• The original “Model B” includes Ethernet, 2 USB ports and originally included 256MB RAM. First shipped in Feb 2012. Can be identified by the lack of mounting holes and “© 2011” on the board
• After late 2012, “Model B” was updated with 512MB RAM. This version can be identified by the two mounting holes and “© 2011,2012” on the board.
• "Model A" was released in early 2013. It lacks Ethernet, has only one USB port, 256MB RAM and is somewhat cheaper than the Model B.
• The "Model B+" released in July 2014 has 4 USB ports, micro SD, lower power consumption, more GPIO pins and 512MB RAM.
• The Raspberry Pi 2 released in February 2015 has 4 USB ports, micro SD slot, a new 900 MHz quad-core ARM Cortex-A7 CPU, 1GB RAM and complete compatibility with Raspberry Pi 1.
• The Raspberry Pi 3 uses the BCM2837 SoC, quad-core 1.2GHz ARM Cortex-A53,1GB LPDDR2 SDRAM, 10/100 Ethernet (via USB).
• The Raspberry Pi 2 v1.2 uses the same SoC as the Raspberry Pi 3 rather than the SoC from earlier Raspberry Pi 2 models.
• The Raspberry Pi 3B+/Pi 3A+ use the BCM2837B0 SoC , 1.4GHz 64-bit quad-core A53 (ARMv8) processor, 1GB/512MB LPDDR2 SDRAM, Gigabit Ethernet (via USB channel, maximum throughput of 300Mb/s)/No Ethernet (A+ model).
• The Raspberry Pi 4 uses the BCM2711 SoC (a re-implementation of BCM283X on 28nm), 1.5GHz quad-core 64-bit ARM Cortex-A72 (ARMv8) processor, 1 (no longer sold), 2, 4, or 8GB of LPDDR4 SDRAM, full-throughput Gigabit Ethernet, dual-band 802.11ac wireless, two USB 3.0 and two USB 2.0 ports, dual 4K monitor support, VideoCore VI graphics, 4Kp60 HEVC video hardware decoding, USB-C power.
• The Raspberry Pi 400 is a modified RPI4 built into a keyboard

The Raspberry Pi Hardware and Raspberry Pi revision codes pages have much more detailed information about models.

FreeBSD has supported the original Raspberry Pi since November, 2012 and Raspberry Pi 2 since March, 2015.

If you have questions, please ask on the freebsd-arm@ mailing list.

• Setting up Xorg on RPi
• RPi 3B+ xorg.conf

As of January 2013, FreeBSD-CURRENT fully supports either a video console (you'll need a USB keyboard and display connected) or it can be configured to use a serial console (you'll need a USB to TTL Serial Cable such as the one sold by Adafruit.com). OTG-capable boards, such as Zero, provide virtual serial console when connected to an USB host.

After connecting video, keyboard, and inserting the SDHC card, you connect power to actually boot.

For Raspberry Pi Zero use the image for RPI-B. For Raspberry Pi 3, Pi 4 and Pi 400 use the image for RPI on 13+.

The default passwords for the images are freebsd/freebsd and root/root .

Raspberry Pi and Raspberry Pi 2 are supported by the Crochet build tool.

Building an image for Raspberry Pi 2

These are a recent feature. Please see this README for more information.

Perl, Python and Ruby wrappers for interfacing with the GPIO ioctl are available at https://github.com/brd/freebsd-gpio

See Raspberry Pi Camera.

Some external displays made for the Raspberry Pi require extra configuration steps to work properly. The Raspberry Pi uses a config.txt file on a FAT partition instead of a traditional BIOS or UEFI firmware. Manufacturers of displays built for Raspberry Pis may provide the relevant settings as part of the documetation. The settings are often the same as on Linux-based distributions for the Raspberry Pi. After writing the bootable image to the compact flash card, mount the FAT partition contained on it as msdosfs and open the config.txt file. This can also be done from within the Pi itself, provided the display gives some form of output, otherwise another machine has to be used. The partition is mounted like this after logging in:

/dev/msdosfs/MSDOSBOOT on /boot/msdos (msdos, local, noatime)

A couple of lines are already present in /boot/msdos/config.txt. The lines from the manufacturer have to be added to the end of that file. After saving and exiting the editor, reboot the Raspberry. The updated config.txt file will be loaded and the display should work as expected.

For example, the following lines were added to config.txt to make a 5“ touchscreen display from Waveshare work and use the proper resolution:

max_usb_current=1
hdmi_group=2
hdmi_mode=87
hdmi_cvt 800 480 60 6 0 0 0
hdmi_drive=1

And the following lines were added to config.txt to make a 9” display from Beetronics work and use the proper resolution:

max_usb_current=1
hdmi_group=2
hdmi_mode=69
hdmi_drive=1

The Pi-Top is a cheap laptop built around the Rpi3

To get the touchpad working add this to your /boot/loader.conf:

usb_quirk_load=YES
ums_load=YES
hw.usb.quirk="0x258a 0x000c 0x0000 0xffff UQ_CFG_INDEX_1"

Device Trees, overlays, and parameters

SDIO

SDIO is implemented in r348805 and we should tether brcmfmac43455-sdio.bin / brcmfmac43455-sdio.txt to get first WIFI network for the RPI4 .

• Booting from a USB connected hard disk - see Bob Prohaska's notes (The hard disk is powered from a powered USB hub.) and Raspberry Pi Boot Modes.

The RPi4 and RPi400 idle at 600MHz but support 1500MHz and 1800MHz respectively.

To enable automatic CPU with powerd(8):

sysctl dev.cpu.0.freq
dev.cpu.0.freq: 600

sysrc powerd_enable="YES"   
/etc/rc.d/powerd restart

If the display defaults to 592×448 under xorg, modify the file /boot/msdos/config.txt with:

hdmi_safe=0

or simply comment out “hdmi_safe=1”

The following additional config.txt setting maybe required, depending on the brand and/or model of monitor used:

max_framebuffers=2
hdmi_force_hotplug=1
hdmi_group=1
hdmi_drive=2
hdmi_mode=16

The FreeBSD-13.1-RELEASE-arm64-aarch64-RPI.img image is known to work with xorg, XFCE, Firefox, and other popular desktop applications. The mouse daemon will start automatically and need not be enabled.

RPi 4 Rev >= 1.2 doesn't boot with FreeBSD-13.0-RELEASE-arm64-aarch64-RPI.img image.

The u-boot.bin used when creating 13.0-RELEASE image was too old to support newer RPi4 hardware revision.

The workaround is replacing u-boot.bin with newer one from sysutils/u-boot-rpi4:

# pkg install -y u-boot-rpi4
# mdconfig -f FreeBSD-13.0-RELEASE-arm64-aarch64-RPI.img
md0
# mount_msdosfs /dev/md0s1 /mnt
cp /usr/local/share/u-boot/u-boot-rpi4/u-boot.bin /mnt/u-boot.bin
# umount /mnt
mdconfig -d -u 0

Reference: How to Check if Your Raspberry Pi 4 Model B is Rev1.2?

Console output is displayed on the HDMI port closest to the USB-C power connector. The other connector only displays the rPI rainbow color screen.